Home → Troubleshooting → @RISK for Excel: Simulation

4. @RISK for Excel: Simulation

4.1. Progress Window Not Displayed during Simulation
4.2. Progress Window Freezes at "Initializing ... 100%"
4.3. Simulation Crashes with Increased Number of Iterations
4.4. Smart Sensitivity Analysis Occurs Even When Disabled
4.5. Calculation Changed to Manual by a Simulation?
4.6. Calculation Changed to Manual while Browsing Results?
4.7. Multiple CPU — Only One CPU Runs
4.8. Multiple CPU — Blocks of Errors in Simulated Outputs
4.9. Multiple Simulations All Show the Same Data
4.10. Correlation Matrix from StatTools Not Accepted
4.11. Change in Output Mean Inconsistent with Sensitivity Tornado
4.12. Same Input Appears Twice in Tornado Graph
4.13. Tornado Graph Is Missing an Input
4.14. Input on Tornado Graph Is Not a Precedent
4.15. Tornado Graph Can't Show All Simulations
4.16. Outputs with Small Means Don't Converge
4.17. Convergence by Standard Deviation: Always Same Number of Iterations
4.18. Missing Results Graph
4.19. Window Opens Briefly, Then Closes
4.20. Can't Move Delimiters or Change Percentages
4.21. Restoring Theoretical Distribution in a Results Graph
4.22. Sum of Percentiles Differs from Percentile of the Sum
4.23. Incorrect Percentiles for Date Distributions
4.24. "Error!" or #QNAN for Distributions in an IF( ) Function
4.25. Reports Do Not Appear after Simulation
4.26. Delimiter Setting Ignored by RiskResultsGraph( )
4.27. Min or Max Setting Ignored by RiskResultsGraph( )
4.28. Template Report Contains Formulas in Place of Numbers
4.29. Unwanted Results Summary Window Appears
4.30. Simulation Used to Run, Now Crashes Excel
4.31. "An exception of unknown type has occurred."
4.32. "Authorization failure" When Simulating
4.33. "Cannot make a sheet to hold correlation information in protected workbook"
4.34. "DTools7_x64.XLL cannot be accessed."
4.35. "Exception of Type PalExcelError" in @RISK 5.x
4.36. "Exception of type PalPipeError"
4.37. "Exception of type PalSystemError" (@RISK 5.0)
4.38. "The formula ... could not be correctly parsed"
4.39. "Found invalid formula ... Continue without detecting RiskMakeInput precedents properly?"
4.40. "Found invalid formula ... Continue without Smart Sensitivity Analysis?"
4.41. "GetPassword cannot be found."
4.42. "Method '~' of object '~' failed" (in Simulation)
4.43. "No inputs collected - no sensitivity results available."
4.44. "No inputs found that affect this output" instead of Tornado Graph
4.45. "No values to graph" Message / All Errors in Simulation Data
4.46. "Non-modal forms cannot be displayed in this host application from an ActiveX DLL, ActiveX control, or Property Page."
4.47. "Not enough memory to run simulation"
4.48. "Object initialized twice" When Launching Palisade Software
4.49. "Object initialized twice" at End of Simulation
4.50. "Open method of Workbooks class failed"
4.51. "Out of Memory"
4.52. "Out of stack space"
4.53. "PalFlexServer6 Application has encountered a problem and needs to close"
4.54. "Protected Workbook: This operation cannot be performed ..."
4.55. "The cell ... is part of an array formula."
4.56. "The correlation matrix ... has multiple inputs assigned to the same matrix position."
4.57. "The correlation matrix ... is not square."
4.58. "The correlation matrix at ... is not self-consistent."
4.59. "The correlation matrix at .... specifies an invalid column."
4.60. "The Excel name "..." has a character not in the current code page."
4.61. "The Excel name "..." refers to "...", which has a character not in the current code page."
4.62. "The exception unknown software exception (0xe06d7363) occurred ..."
4.63. "The RiskMakeInput distribution ... may not be correlated."
4.64. "The worksheet name '...' has a character not in the current code page."
4.65. "This selection isn't valid" in Quick Reports
4.66. "Type mismatch" at End of Simulation

← All Products: Other Issues @RISK for Excel: Optimization (RISKOptimizer) →